V-Hold Woodworking Machinery Co., Ltd.
V-Hold Woodworking Machinery Co., Ltd.
Add to Cart
Practical Woodworking machine Five Head Four Side Moulder for wooden stair rail,Feeding speed 6-36m/min
| Four Side Planer VH-M516 and VH-M518 both have 5 heads with same motor power, there are one left spindle,
one right spindle, one upper spindle and two spindles on the bottom. Each spindles have its own Motor, which
can guarantee the power for cutting. Our planer use Inverter to feed, speed range is 6-36m/min.
Both Planers have High rigid body structure, as it was made from cast iron. The damping performance and the
rigidity of the machine body would be better compared with steel. So laying a good foundation for the smooth
running of the cutter shaft and feeding system.
Adopting hard chromed worktable to minimize abrasion, and enhance operational life span. Planers are
configured the short material auxiliary device in the front, can effectively improve the smooth feeding of short
material.
The only difference between VH-M516 and VH-M518 are their processing width, for VH-M516 can only process
materials no wider than 160mm, VH-M518 can process bigger materials with 180mm width. It depends on what
kinds of wood materials customer use.
|
 | |
| VH-M516 and VH-M518 can be used for
processing Soft wood strip, Medium cutting
capacity strip, MDF strip, HDF strip, Glued
laminated timber and Square boards. For
wooden furniture and wood profile processing. |
| Model | VH-M518 | VH-M516 | |
| Specification | Working width | 25-180 | 25-160 |
| Working thickness | 8-130 | 8-120 | |
| Working table length | 1500 | 1500 | |
| Feeding speed | 6-36 | 6-36 | |
| Main spindle diameter (mm) | Φ 40 | Φ 40 | |
| Main spindle revolution (r/min) | 6500 | 6500 | |
| Air pressure (Mpa) | 0.6 | 0.6 | |
| Motor power (KW) | 1st Lower Shaft | 4kw/5.5HP | 4kw/5.5HP |
| Right vertical spindle | 4kw/5.5HP | 4kw/5.5HP | |
| Left vertical spindle | 4kw/5.5HP | 4kw/5.5HP | |
| 1st Upper Shaft | 5.5kw/7.5HP | 5.5kw/7.5HP | |
| 2nd Upper Shaft | / | / | |
| 2nd Lower Shaft | 4kw/5.5HP | 4kw/5.5HP | |
| Feeding beam lifting | 0.55kw/0.75HP | 0.55kw/0.75HP | |
| Feeding motor | 3kw/4HP | 3kw/4HP | |
| Total power | 25.05kw/34HP | 25.05kw/34HP | |
| Cutter diameter | 1st Lower Shaft | Φ 125 | Φ 125 |
| Right Vertical spindle | Φ 125-Φ 160 | Φ 125-Φ 160 | |
| Left vertical spindle | Φ 125-Φ 160 | Φ 125-Φ 160 | |
| 1st Upper Shaft | Φ 125-Φ 160 | Φ 125-Φ 160 | |
| 2nd Lower Shaft | Φ 125-Φ 180 | Φ 125-Φ 180 | |
| Remark | Feeding wheel diameter (mm) | Φ140 | Φ140 |
| Dust outlet diameter (mm) | Φ140 | Φ140 |
Keep improving, focus on every detail
High rigid body structure: The lathe bed is of integral structure, being made of casting with damping perfor
mance ,and the rigidity of the lathe bed is better .Laying a good foundution for the smooth running of the cutter shaft
and feeding system.